Design & Price a Rotating Wood Slat Room Divider
Slats that turn. Open, the divider reads as a screen and the two spaces stay connected; closed, it becomes a solid wall of wood — the ROTERA system. Enter your wall width and ceiling height, choose how the slats sit when they're closed, and the designer returns the slat count and the price. Ceilings up to 9 ft.
Not sure how to measure? See the measuring guide →
How the ROTERA system works
Every slat sits between a ceiling bracket and a floor bracket, with a cap at each end and a push pin that lets it pivot in place. Turn the slats and you change what the divider does: face-on they close the room off, edge-on they almost disappear and the sightline opens up. Nothing slides or folds — the run stays exactly where it is and only the angle changes.
It is a self-aligning system, which is what makes it a realistic job to install yourself: a guide tool sets the bracket positions so the slats line up without measuring each one. The ROTERA installation guide has the full sequence and the hardware list.
Overlapping or flat closed
This is the one choice on this page that changes the product rather than the price, so it's worth understanding before you pick.
- Overlapping — the slats overlap each other when turned closed, leaving no gap at all. Choose this when the divider has to give full privacy: a bedroom off an open plan, a home office, a stairwell you want to shut off visually.
- Flat closed — the slats sit flat in line with a ½″ gap between them when closed. Nearly private, but air and a little light still pass, and the closed position reads as a flatter, more even wall.
Either way, the gap you get when the slats are turned open is the slat width minus 2″ — so a wider profile opens up more. The designer shows the spacing it has worked out for your choice before you add to cart.
How to measure
- Width — the horizontal run the divider will cover, wall to wall or wall to open end.
- Ceiling height — floor to ceiling at the run itself. Maximum 108″ (9 ft).
Measure the height at both ends. Floors and ceilings are rarely dead level, and since each slat is cut on site you'll want to know that before you start rather than halfway along the run.
See also: finding plumb points and how many slats do I need?
Cutting and installing on site
Slats ship at full length and are cut down on site. Cut each one 11/16″ (18 mm) shorter than the floor-to-ceiling distance at its position, which leaves room for the caps and the bracket hardware. If you want to be able to lift slats out again later, leave about ¼″ of extra clearance at the top.
The ceiling brackets need a 7/16″ hole; the floor brackets screw down. Both ends are fixed, so this is a permanent installation rather than a freestanding screen.
Finishes and slat profiles
Available in Walnut, Dark Walnut, White Oak, Unfinished/Stainable and Paintable MDF, in three profiles: 2″ × 4″ standard, 2″ × 5″ mid and 2″ × 6″ bold. Profile matters more here than on a fixed divider, because it sets both how solid the closed position looks and how open the open position feels. Order a sample before you commit to a finish — screens never get wood colour right.
Questions about rotating wood slat dividers
How tall can a rotating divider be?
Up to 108″ (9 ft). For a taller run, a fixed FIXERA divider handles ceilings to 12 ft using extensions.
Do I cut the slats, or do you?
You do. Slats ship at full length and are cut on site to 11/16″ (18 mm) less than your floor-to-ceiling measurement, so the caps and brackets fit.
How much privacy do I get when the slats are closed?
With the overlapping pattern, full privacy — the slats overlap with no gap. With flat closed, a ½″ gap remains between slats.
Does it need to be fixed to the floor?
Yes. Ceiling brackets and floor brackets both take the slat, so the divider is fixed at each end. It is not a freestanding or temporary screen.
Is there a minimum order?
Yes, 12 slats. If your dimensions work out to fewer, the estimate rounds up to the minimum.
Rotating or fixed — which should I choose?
Rotating if the room needs to be two different rooms at different times of day. Fixed if the divider is purely architectural and the sightline never needs to change — price one on the FIXERA designer.
